Danh Mục Sản Phẩm

MR-JE-10A Bộ điều khiển động cơ Servo Mitsubishi 0.1 KW

Mã Sản Phẩm
: MR-JE-10A
Tên Sản Phẩm
: MR-JE-10A Bộ điều khiển động cơ Servo Mitsubishi 0.1 KW
Danh Mục
: Servo Driver
Thương Hiệu
: Servo Driver MR-JE
Giá

: Liên Hệ



MR-JE-10A Bộ điều khiển động cơ Servo Mitsubishi 0.1 KW

Chi Tiết Sản Phẩm


MR-JE-10A Bộ điều khiển động cơ Servo Mitsubishi 0.1 KW

  • Bộ điều khiển động cơ Servo Mitsubishi dòng MR-JE-A
  • Điện áp hoạt động:
    • 3 pha 220VAC
    • 1 pha 220VAC
  • Công suất: 100W
  • Phần mềm cấu hình: Mr Configurator 2-SW1DNC-MRC2-E
    • Cáp Encoder kết nối Bộ điều khiển MR-JE với động cơ Servo Motor: Cáp Encoder MR-JE
    • Cáp Nguồn kết nối Bộ điều khiển MR-JE với động cơ Servo Motor: Cáp nguồn MR-JE
    • Cáp phanh kết nối Bộ điều khiển MR-JE với động cơ Servo Motor: Cáp phanh MR-JE

Thông số kỹ thuật:

Servo amplifier model MR-JE- 10A 20A 40A 70A
Output Rated voltage 3-phase 170 V AC
Rated current [A] 1.1 1.5 2.8 5.8
Power supply input Voltage/frequency (Note 1) 3-phase or 1-phase 200 V AC to 240 V AC,
50 Hz/60 Hz
Rated current (Note 7) [A] 0.9 1.5 2.6 3.8
Permissible voltage fluctuation 3-phase or 1-phase 170 V AC to 264 V AC
Permissible frequency fluctuation ±5% maximum
Interface power supply 24 V DC ± 10% (required current capacity: 0.3 A)
Control method Sine-wave PWM control/current control method
Tolerable regenerative power of the
built-in regenerative resistor (Note 2, 3) [W]
- - 10 20
Dynamic brake Built-in (Note 4, 8)
Communication function USB: Connect a personal computer (MR Configurator2 compatible) RS-422: Connect a controller (1 : n communication up to 32 axes) (Note 6)
Encoder output pulse Compatible (A/B/Z-phase pulse)
Analog monitor 2 channels
Position control mode Maximum input pulse frequency 4 Mpulses/s (when using differential receiver), 200 kpulses/s (when using open-collector)
Positioning feedback pulse Encoder resolution: 131072 pulses/rev
Command pulse multiplying factor Electronic gear A/B multiple, A: 1 to 16777215, B: 1 to 16777215, 1/10 < A/B < 4000
Positioning complete width setting 0 pulse to ±65535 pulses (command pulse unit)
Error excessive ±3 rotations
Torque limit Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Speed control mode Speed control range Analog speed command 1:2000, internal speed command 1:5000
Analog speed command input 0 V DC to ±10 V DC/rated speed (Speed at 10 V is changeable with [Pr. PC12].)
Speed fluctuation rate ±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%)
±0.2% maximum (ambient temperature: 25 °C ± 10 °C) only when using analog speed command
Torque limit Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Torque control mode Analog torque command input 0 V DC to ±8 V DC/maximum torque (input impedance: 10 kΩ to 12 kΩ)
Speed limit Set by parameters or external analog input (0 V DC to ± 10 V DC/rated speed)
Servo function Advanced vibration suppression control II, adaptive filter II, robust filter, auto tuning, one-touch tuning, tough drive function, drive recorder function, machine diagnosis function, power monitoring function
Protective functions Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error protection, regenerative error protection, undervoltage protection, instantaneous power failure protection, overspeed protection,
error excessive protection
Compliance to standards Refer to "Conformity with global standards and regulations" on p. 17 in this catalog.
Structure (IP rating) Natural cooling, open (IP20)
Close mounting Possible (Note 5)
Environment Ambient temperature Operation: 0 °C to 55 °C (non-freezing), storage: -20 °C to 65 °C (non-freezing)
Ambient humidity Operation/Storage: 90 %RH maximum (non-condensing)
Ambience Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
Altitude 1000 m or less above sea level
Vibration resistance 5.9 m/s2 at 10 Hz to 55 Hz (directions of X, Y and Z axes)
Mass [kg] 0.8 0.8 0.8 1.5

Kết hợp động cơ Servo Motor:

Servo amplifier Servo motor
HF-KN series HF-SN series
MR-JE-10A HF-KN13J -
MR-JE-20A HF-KN23J -
MR-JE-40A HF-KN43J -
MR-JE-70A HF-KN73J HF-SN52J
MR-JE-100A - HF-SN102J
MR-JE-200A - HF-SN152J, HF-SN202J
MR-JE-300A - HF-SN302J

 

Servo amplifier Servo motor
HG-KN series HG-SN series
MR-JE-10B/MR-JE-10A HG-KN13J -
MR-JE-20B/MR-JE-20A HG-KN23J -
MR-JE-40B/MR-JE-40A HG-KN43J -
MR-JE-70B/MR-JE-70A HG-KN73J HG-SN52J
MR-JE-100B/MR-JE-100A - HG-SN102J
MR-JE-200B/MR-JE-200A - HG-SN152J, HG-SN202J
MR-JE-300B/MR-JE-300A - HG-SN302J

 

MR-JE-10A Bộ điều khiển động cơ Servo Mitsubishi 0.1 KW

 


Tin Mới

Sản Phẩm Nổi Bật